Blomberg Washer Error Codes

Expert Tips

Welcome to your go-to guide for understanding Blomberg washer error codes! If your Blomberg washing machine is flashing a code you don’t recognize, you’ve come to the right place. Here, we’ve gathered all the error codes for Blomberg washers in one spot. Whether it’s a mysterious beep or a blinking light, we’ll help you figure out what your washer is trying to tell you. Our explanations are simple and straightforward, making it easy for everyone to follow along. No need to scratch your head in confusion or spend hours searching online. From common issues to the less familiar ones, we cover everything. Let’s dive in and get your Blomberg washer running smoothly again.

Quick Solutions for Resolving Error Codes on Blomberg washers

Troubleshooting Blomberg Washer Error Codes

Verify the error code: Double-check the washer’s display to ensure the error code is correctly noted. Display panels can sometimes make certain characters look similar, leading to confusion.
Reference the user manual: Look for the error code list in the user manual for your specific washer model, which often includes suggested troubleshooting steps.
Attempt a reset: Unplugging the washer for a few minutes and then plugging it back in can reset the system, potentially clearing the error.
Seek professional help: If the error code remains unclear or the problem persists after attempting a reset, it’s advisable to contact a professional appliance repair service for further assistance. Contact us to service your washer.

Repairing a washer often involves dealing with electrical components, a task that can be complex and hazardous, especially for those not familiar with appliance repair and electrical safety. If you are unsure about what you are doing or lack the necessary experience, it is strongly recommended to seek professional assistance. A qualified technician can provide an accurate diagnosis and ensure safe repairs, reducing the risk of injury or further damage to the appliance.

Error Code 01

The Blomberg Washer error code “01” indicates a Water Inlet Fault, meaning the washer is not filling with water as expected during the start of a wash cycle. This issue can prevent the washing machine from operating properly, as sufficient water intake is crucial for washing clothes.

Possible Causes:

Closed Water Supply Valves: The valves supplying water to the washer might be turned off, preventing water from entering the machine.
Clogged Inlet Filters: The filters at the water inlet hose connections could be clogged with sediment or debris, restricting water flow.
Faulty Water Inlet Valve: The electronic valve that controls the flow of water into the washer may be malfunctioning or failed, leading to inadequate water supply.
Kinked or Damaged Supply Hoses: The hoses that connect the washer to the home water supply could be kinked, twisted, or damaged, restricting water flow.
Pressure Issues: Very low water pressure in the home’s supply can impede the washer’s ability to fill properly.

Fixes:

Check Water Supply Valves: Ensure that the water supply valves are fully open. These valves are typically located behind or near the washer.
Clean Inlet Filters: Disconnect the water supply hoses from the back of the washer to access the inlet filters. Clean the filters gently with a soft brush or cloth to remove any debris.
Inspect Water Inlet Valve: Test the water inlet valve with a multimeter for continuity. If the valve is defective, it will need to be replaced.
Examine Supply Hoses: Check the hoses for any kinks, twists, or damage that could obstruct water flow. Straighten out kinks or replace the hoses if damaged.
Verify Water Pressure: If possible, measure the water pressure in your home to ensure it meets the washer’s minimum requirements. You may need to consult a plumber if water pressure is consistently too low.
Professional Assistance: If the above steps do not resolve the issue, it may be best to seek professional help. A qualified appliance repair technician can diagnose and fix more complex problems related to the water inlet system or the washer’s electronics.

Error Code 02

The Blomberg Washer error code “02” signifies a Drain Error, indicating that the washer is experiencing issues with draining water from the drum. This problem can disrupt the washing cycle, preventing the machine from moving on to subsequent phases or completing the cycle properly.

Possible Causes:

Clogged Drain Filter: The washer’s drain filter, designed to catch debris and prevent it from reaching the pump, may be clogged.
Blocked Drain Hose: The hose that routes water from the washer to the drain system might be kinked, twisted, or clogged with debris.
Faulty Drain Pump: The pump responsible for moving water out of the washer could be malfunctioning or obstructed.
Drain System Issue: There might be a problem with the household drain system itself, such as a clog or blockage in the plumbing that prevents water from flowing out efficiently.

Fixes:

Clean the Drain Filter: Locate and clean the washer’s drain filter according to the manufacturer’s instructions. This often involves removing, rinsing, and reinserting the filter.
Inspect and Clear the Drain Hose: Ensure the drain hose is not kinked or twisted. Detach the hose and flush it with water to remove any clogs.
Check the Drain Pump: Access the drain pump to check for obstructions or damage. You may need to remove debris or replace the pump if it’s faulty.
Examine Household Drainage: Ensure that the sink or standpipe where the washer drains is not clogged. You may need to use a plumber’s snake or a similar tool to clear blockages in the household plumbing.
Professional Assistance: If the issue persists after you’ve checked the filter, hose, and pump, and ensured that the household drainage is clear, the problem might be more complex and require professional diagnosis and repair.
Reset the Washer: Sometimes, resetting the washer by unplugging it for a few minutes and then plugging it back in can resolve electronic glitches that might be causing the drain error.

Addressing a Code 02 error on a Blomberg Washer involves ensuring that the entire drainage path, from the drain filter to the household plumbing, is clear of obstructions and functioning properly. Regular maintenance, such as cleaning the drain filter and checking the drain hose, can help prevent drainage issues.

Error Code 03

The Blomberg Washer error code “03” indicates a Heating Error, meaning the water in the washer is not heating up to the required temperature for the selected wash cycle. This issue can affect cleaning performance, particularly on cycles designed for higher temperatures to remove stains or sanitize clothing.

Possible Causes:

Faulty Heating Element: The element responsible for heating the water might be damaged or malfunctioning.
Malfunctioning Thermostat or NTC Sensor: The thermostat or NTC (Negative Temperature Coefficient) sensor, which monitors water temperature, could be failing to accurately gauge or control the temperature.
Wiring Issues: Problems with the wiring connections between the heating element, thermostat/NTC sensor, and the main control board can disrupt heat control.
Control Board Failure: The main control board may have an issue that prevents it from properly activating the heating element or interpreting temperature sensor readings.

Fixes:

Check the Heating Element: Use a multimeter to test the continuity of the heating element. A lack of continuity indicates the element needs replacement.
Inspect the Thermostat/NTC Sensor: Test the thermostat or NTC sensor for proper function. These components should offer accurate temperature readings; if not, they need to be replaced.
Examine Wiring and Connections: Look for any loose, damaged, or corroded wiring between the heating element, thermostat/NTC sensor, and control board. Repair or replace as necessary.
Reset the Washer: Disconnecting the washer for a few minutes can reset the system, potentially resolving minor electronic glitches that might be affecting the heating function.
Professional Repair: Due to the complexity of diagnosing and repairing heating issues, which involve electrical components and potentially high voltages, it’s advisable to seek professional assistance. A qualified technician can safely assess and fix the problem.
Consult the User Manual: Some washers have specific diagnostic modes or reset procedures that can address system errors. Refer to your washer’s user manual for any model-specific instructions or troubleshooting steps.

Error Code 07

The Blomberg Washer error code “07” indicates a Door Lock Error, meaning the washing machine’s control system has detected an issue with the door not being properly locked or closed. This error is crucial because the washer will not start a cycle until it confirms that the door is securely locked to ensure safety during operation.

Possible Causes:

Faulty Door Latch or Lock Mechanism: The mechanism that locks the washer door could be damaged or malfunctioning, preventing it from securing the door properly.
Door Misalignment: The door itself may be misaligned, preventing it from closing fully or engaging the lock mechanism correctly.
Damaged Door Seal: A damaged or obstructed door seal can prevent the door from closing fully, which could be interpreted as a locking issue.
Control Board or Wiring Issues: Problems with the wiring or the control board related to the door lock circuit could prevent the door lock mechanism from functioning correctly.

Fixes:

Inspect and Clean the Door Lock Mechanism: Check the door lock for any visible signs of damage, debris, or obstruction. Clean the lock mechanism gently to remove any buildup that could impede its function.
Check Door Alignment and Seal: Ensure the door is properly aligned in its frame and that the seal is intact, clean, and free of obstructions. Adjust the door alignment or replace the seal if necessary.
Test the Door Lock Mechanism: If possible, use a multimeter to test the door lock for continuity. A lack of continuity indicates the lock may need to be replaced.
Examine Wiring and Connections: Inspect the wiring connections between the door lock and the control board. Repair or replace any damaged wires or connectors.
Reset the Washer: Unplug the washer for a few minutes to reset the electronic controls, which might resolve a temporary glitch causing the error.
Professional Repair: If the issue persists, it’s advisable to seek professional assistance. A qualified appliance repair technician can accurately diagnose and repair problems with the door lock mechanism, control board, or electrical connections.

Resolving a Code 07 door lock error in a Blomberg Washer involves ensuring the door can close and lock properly, which may require adjustments or replacements of the door lock mechanism, seal, or addressing alignment issues. Due to the safety implications of a malfunctioning door lock, addressing this error promptly and correctly is crucial.

Error Code 09

The Blomberg Washer error code “09” indicates a Program Selection Error. This error suggests that there’s an issue with the washer’s ability to select or initiate the chosen wash program, potentially due to a malfunction in the user interface, the main control board, or communication problems between them.

Possible Causes:

Faulty User Interface: The control panel or user interface might be malfunctioning, preventing proper selection or initiation of wash programs.
Control Board Issues: The main control board, which interprets inputs from the user interface and initiates the selected wash program, could be experiencing problems.
Software Glitches: Temporary software or firmware glitches in the washer’s electronics can disrupt program selection and operation.
Communication Problems: Issues with the wiring or connections between the user interface and the main control board can interfere with the exchange of selection commands.

Fixes:

Reset the Washer: Often, a simple reset can clear temporary software glitches. Unplug the washer for a few minutes, then plug it back in to see if the issue resolves.
Inspect the User Interface: Check the control panel for any signs of damage or malfunction. Ensure all buttons or touch areas are responsive.
Check Wiring and Connections: Inspect the wiring harnesses and connections between the user interface and the main control board for looseness, damage, or corrosion. Secure or replace as needed.
Update Firmware: If your model supports firmware updates, check for and install any available updates that might address known issues with program selection.
Professional Diagnosis and Repair: If the problem persists, the issue may require a deeper technical assessment. A professional appliance repair technician can diagnose and repair faults in the user interface, control board, or software.
Consult the User Manual: Some washers have specific procedures to troubleshoot or reset the electronics. Refer to your washer’s user manual for any model-specific instructions or troubleshooting tips.

Error Code 10

The Blomberg Washer error code “10” signifies an Overfill Error, indicating that the machine has detected an excessive amount of water in the drum, surpassing the intended level for the selected wash program. This condition can pose risks of water leakage, damage to the machine, and inefficient washing.

Possible Causes:

Faulty Water Inlet Valve: The valve may not be closing properly, allowing water to continue flowing into the washer even after reaching the desired level.
Malfunctioning Pressure Switch: The pressure switch, responsible for detecting the water level in the drum and signaling the control board to stop filling, might be faulty.
Blocked or Damaged Pressure Hose: A blockage or damage in the hose connected to the pressure switch can prevent accurate water level detection.
Control Board Issues: The washer’s main control board could fail to process the signals correctly from the pressure switch, resulting in overfilling.
Software Glitches: Temporary software issues can also lead to improper operation of the filling mechanism.

Faulty Water Level Pressure Switch: The switch or sensor that monitors the water level might be malfunctioning, leading to inaccurate readings.
Blocked Pressure Hose: The hose that connects the tub to the pressure switch could be clogged or kinked, impairing the sensor’s ability to monitor water pressure accurately.
Wiring or Connection Issues: Problems with the electrical connections between the pressure switch and the control board can disrupt signal transmission.
Control Board Problems: A malfunction within the washer’s main control board could affect how pressure sensor signals are processed.

Fixes:

Inspect the Water Inlet Valve: Check if the inlet valve shuts off water flow once the machine is powered off. If water continues to flow, the valve may need to be replaced.
Test the Pressure Switch: Use a multimeter to test the pressure switch for continuity. Also, ensure that the switch’s settings correspond to the correct water levels as per the manufacturer’s specifications.
Check the Pressure Hose: Examine the hose for any signs of blockage or damage. Clear any blockages found, and replace the hose if it’s damaged to ensure accurate water level detection.
Reset the Washer: Disconnect the washer for a few minutes to reset the control board, which might help in resolving temporary software or electronic glitches.
Professional Assistance: Given the technical nature of diagnosing and repairing an overfill error, which involves electrical components and water management systems, professional service is recommended. A qualified technician can accurately identify and fix the issue.
Consult the User Manual: Refer to your washer’s user manual for any specific troubleshooting steps or reset procedures recommended by the manufacturer.

Error Code 11

The Blomberg Washer error code “11” indicates a Water Heating Fault, meaning the washer is unable to heat the water to the required temperature for the selected program. This malfunction can affect the efficiency of washing programs that rely on hot water to clean clothes properly.

Possible Causes:

Faulty Heating Element: The heating element responsible for warming the water may be damaged or malfunctioning.
Malfunctioning NTC (Temperature Sensor): The NTC sensor, which monitors water temperature, could be faulty, providing inaccurate readings.
Wiring Issues: There could be a problem with the wiring or connections between the heating element, NTC sensor, and the main control board.
Control Board Problems: The washer’s main control board might be failing to send power to the heating element or to interpret signals from the temperature sensor correctly.

Fixes:

Inspect and Test the Heating Element: Use a multimeter to check the continuity of the heating element. If there’s no continuity, the element needs replacement.
Check the NTC Sensor: Test the NTC sensor for resistance. The resistance should change with temperature; if it doesn’t, the sensor may need replacing.
Examine Wiring and Connections: Look for any loose, damaged, or corroded wiring and connections between the heating element, NTC sensor, and control board. Repair or replace as necessary.
Reset the Washer: Disconnecting the washer for a few minutes can sometimes clear temporary electronic glitches that might be causing the error.
Professional Repair: Due to the complexity of water heating issues and the potential for electrical hazards, it’s advisable to seek professional assistance. A qualified technician can diagnose and repair issues related to the heating element, sensors, or control board.

Error Code 13

The Blomberg Washer error code “13” indicates a Spin Speed Error, signifying that the washer is having trouble reaching or maintaining the selected spin speed during the spin cycle. This error can affect the efficiency of the spin cycle, potentially leaving clothes wetter than expected at the end of the wash.

Possible Causes:

Imbalanced Load: An unevenly distributed load can cause the washer to become imbalanced, making it difficult to achieve the correct spin speed.
Faulty Motor: Problems with the washer’s motor, including wear or electrical issues, can prevent it from spinning at the desired speed.
Worn Drive Belt: A stretched or worn drive belt might slip or fail to transfer sufficient power from the motor to the drum.
Malfunctioning Speed Sensor or Tachometer: The sensor that monitors the drum’s speed could be faulty, leading to incorrect spin speed detection.
Control Board Issues: The main control board may not be correctly regulating the motor’s speed due to a software glitch or hardware malfunction.

Fixes:

Redistribute Laundry Load: Open the washer and redistribute the laundry more evenly within the drum. Try the spin cycle again to see if the issue resolves.
Inspect the Motor and Drive Belt: Check the motor for signs of wear or damage and test its function. Examine the drive belt to ensure it’s tight and in good condition, replacing it if necessary.
Test the Speed Sensor/Tachometer: If accessible, test the speed sensor or tachometer with a multimeter to ensure it’s functioning correctly. Replace the sensor if it’s found to be faulty.
Reset the Washer: Unplug the washer for a few minutes to reset the electronics, which might correct temporary software issues affecting spin speed control.
Professional Diagnosis and Repair: If the problem persists, professional repair is advisable. A technician can provide a comprehensive assessment of the motor, control board, and related components, ensuring accurate diagnosis and effective repair.
Refer to the User Manual: Some washers have specific calibration or diagnostic modes that can address issues with spin speed. Consult the washer’s manual for any model-specific procedures that might help.

Resolving a Code 13 spin speed error involves checking for mechanical issues that could affect the drum’s rotation, ensuring the laundry is evenly distributed, and potentially seeking professional assistance if the issue is related to the motor or control board. Regular maintenance, such as checking the drive belt and redistributing laundry loads, can help prevent such errors.

Error Code 18

The Blomberg Washer error code “18” indicates an issue with the Incorrect Mains Frequency or Voltage, suggesting that the electrical supply to the washer does not match the appliance’s required specifications for either voltage or frequency. This condition can affect the washer’s performance, potentially causing it to malfunction or not operate at all.

Possible Causes:

Voltage Fluctuations: The home’s electrical supply may be experiencing fluctuations that fall outside the washer’s required operational range, either too high or too low.
Incorrect Frequency: Electrical appliances are designed to operate at a specific frequency (measured in Hz). If the mains frequency does not align with what the washer is designed for, it can lead to operational issues.
Electrical Supply Issues: Problems with the home’s electrical circuit, including outdated wiring or an overloaded circuit, can contribute to incorrect voltage or frequency.
Regional Mismatch: If the washer was manufactured for a different region with different electrical standards, there could be a mismatch in the required voltage or frequency.

Fixes:

Verify Electrical Specifications: Check the washer’s manual for its voltage and frequency requirements. Use a multimeter to measure the outlet’s voltage and compare it with your local electrical standards to ensure compatibility.
Consult with Utility Provider: If you suspect that the issue lies with fluctuating or incorrect voltage/frequency from your utility provider, contact them for an assessment and possible solutions.
Evaluate the Electrical Circuit: Have a licensed electrician inspect the home’s electrical circuit supplying the washer to identify and correct any issues, such as outdated wiring or an overloaded circuit.
Use a Voltage Stabilizer or Converter: If voltage fluctuations are a consistent issue, consider using a voltage stabilizer. If there’s a regional mismatch, a voltage converter or transformer may be necessary to match the washer’s requirements.
Professional Assessment: For complex issues related to electrical supply or if the washer continues to display error code “18,” professional appliance repair service is recommended. They can offer solutions tailored to your specific situation, potentially including adjustments to the appliance itself.

Safety Reminder

Taking clothes out and restarting your washer is easy. But, fixing sensor problems or control board issues needs special skills and safety steps. If you’re not sure how to fix your washer, it’s best to get help from professionals. This makes sure the checks are right and the repairs are safe. Regular upkeep and following the usage tips can stop mistakes. Call ARNI Services for reliable Blomberg washing machine repair.

Get Your Blomberg Washing Machine Fixed Right

If you managed to troubleshoot and fix your washer, that's great! But if you're not a technical person or couldn't solve the problem, that's why our technicians are here. We can help figure out what's really going on. Sometimes, even though the error seems like one thing, the real issue might be something else. That's why it's important to have a professional do a proper diagnostic to find the problem and fix it the right way. Contact us today, and we'll schedule a technician to come and check your Blomberg washer so you can have dry clothes again.

Schedule Service